What is Sea Surface Temperature (SST) ?

What is Sea Surface Temperature (SST) ?

Postby yiboj » Mon Feb 08, 2016 10:24 am

Understanding Sea Surface Temperature

Sea Surface Temperature (SST) is a challenging parameter to define precisely as the upper ocean (~10 m) has a complex and variable vertical temperature structure that is related to ocean turbulence and air-sea fluxes of heat, moisture and momentum. A theoretical framework is therefore required to understand the information content and relationships between measurements of SST made by different satellite and in situ instruments, especially if these are to be merged together. The definitions of SST developed by the Group for High-Resolution Sea Surface Temperature (GHRSST) SST Science Team (agreed at the 2nd and 3rd workshops) achieve the closest possible coincidence between what is defined and what can be measured, taking into account current scientific knowledge and understanding of the near surface thermal structure of the ocean.

Definitions of SST within the GHRSST

The figure below presents a schematic diagram that summarises the definition of SST in the upper 10 m of the ocean and provides a framework to understand the differences between complementary SST measurements. It encapsulates the effects of dominant heat transport processes and time scales of variability associated with distinct vertical and volume regimes of the upper ocean water column (horizontal and temporal variability is implicitly assumed).

Each of the definitions marked in the bottom right of the figure is explained in the following sub-sections.

newerSSTdef.gif
Hypothetical vertical profiles of temperature for the upper 10m of the ocean surface in high wind speed conditions or during the night (red) and for low wind speed during the day (black)
newerSSTdef.gif (19.59 KiB) Viewed 14989 times


The interface temperature (SSTint)

At the exact air-sea interface a hypothetical temperature called the interface temperature (SSTint) is defined although this is of no practical use because it cannot be measured using current technology.

The skin sea surface temperature (SSTskin)

The skin temperature (SSTskin) is defined as the temperature measured by an infrared radiometer typically operating at wavelengths 3.7-12 µm (chosen for consistency with the majority of infrared satellite measurements) that represents the temperature within the conductive diffusion-dominated sub-layer at a depth of ~10-20 µm. SSTskin measurements are subject to a large potential diurnal cycle including cool skin layer effects (especially at night under clear skies and low wind speed conditions) and warm layer effects in the daytime.

The sub-skin sea surface temperature (SSTsub-skin)

The subskin temperature (SSTsubskin) represents the temperature at the base of the conductive laminar sub-layer of the ocean surface. For practical purposes, SSTsubskin can be well approximated to the measurement of surface temperature by a microwave radiometer operating in the 6-11 GHz frequency range, but the relationship is neither direct nor invariant to changing physical conditions or to the specific geometry of the microwave measurements.

The surface temperature at depth (SSTz or SSTdepth)

All measurements of water temperature beneath the SSTsubskin are referred to as depth temperatures (SSTdepth) measured using a wide variety of platforms and sensors such as drifting buoys, vertical profiling floats, or deep thermistor chains at depths ranging from 10-2 - 103m. These temperature observations are distinct from those obtained using remote sensing techniques (SSTskin and SSTsubskin) and must be qualified by a measurement depth in meters (e.g., or SST(z) e.g. SST5m).

The foundation temperature (SSTfnd)

The foundation SST, SSTfnd, is the temperature free of diurnal temperature variability, i.e., SSTfnd is defined as the temperature at the first time of the day when the heat gain from the solar radiation absorption exceeds the heat loss at the sea surface. For conditions, when the SST increases or decreases monotonically over several days, the Tfnd occurs on a given day when the time rate of change of temperature is at a minimum (increasing SST), or a maximum (decreasing SST). If such a point in the daily time series cannot be identified, the SSTfnd should be set to a clearly stated time. SSTfnd is named to indicate that it is the foundation temperature upon which the growth and decay of the diurnal heating develops each day. Only in situ contact thermometry is able to measure SSTfnd and analysis procedures must be used to estimate the SSTfnd from radiometric retrievals of SSTskin and SSTsubskin taken at other times of the day.

The figure below provides an example of SSTfnd.
Tfnd.jpg
Tfnd.jpg (32.8 KiB) Viewed 15054 times


Please refer to GHRSST for detail information https://www.ghrsst.org/ghrsst-data-services/products/.
yiboj
 
Posts: 97
Joined: Mon Mar 30, 2015 11:22 am

Re: What is Sea Surface Temperature (SST) ?

Postby mark112 » Sun Aug 14, 2016 4:13 am

Very Useful Infomation
mark112
 
Posts: 1
Joined: Sun Aug 14, 2016 4:04 am

Re: What is Sea Surface Temperature (SST) ?

Postby niscope » Sun Oct 27, 2019 2:17 pm

I am trying to access the GHRSST Level 4 CMC0.1deg Global Foundation Sea Surface Temperature Analysis (GDS version 2) dataset. When I plot the temperature while sweeping across the longitudes (relevant code: https://github.com/nasa/podaac_tools_an ... _animation), I see that the temperature over the landmass is nonzero. How can I mask these values so that I just have the sea surface temperature and not the landmass temperature data?
niscope
 
Posts: 1
Joined: Sun Oct 27, 2019 2:06 pm

Re: What is Sea Surface Temperature (SST) ?

Postby yiboj » Sun Nov 10, 2019 1:29 pm

Hi,
Thanks for your inquiry.
You can use the mask variable in the data file, land is represented by mask = 2 and mask = 1 means water. Please try and let us know.
Regards,
-PODAAC DE
yiboj
 
Posts: 97
Joined: Mon Mar 30, 2015 11:22 am


Return to General Questions

cron